Siemens SIMOTION TM15 Commissioning Manual Download Page 53

Page: 53 / 99

Error messages

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

Error codes

Table 4- 1

Error codes (for hotline)

ERROR CODE 35...

BITS

DESCRIPTION

REMEDY

...801 to

...905

Internal module error
or
communication problem
on DRIVE CLiQ

interface

Replace the module

and contact your local

technical support.

...906

At least one of the

terminals for the I/O

power supply is not

connected
or
the I/O power supply is

outside of the specified

range.
If the error is no longer

present, the error code

is retracted

automatically.

Check all terminals for

the I/O power supply.

...907

FPGA

FPGA programming

error (TM17 High

Feature only)

Try to update the

firmware.

If error is still present,

replace the module and

contact your local

technical support.

The error code (see table above) is stored as parameter P2122 in the SINAMICS Control

Unit. This code can be read by the user task with the "readDriveParameter" system function

(see SIMOTION documentation "Reference List – System Functions / Variables").
Another option is to use the BICO technology editor to link parameter P2122 with an I/O

word that has been added to one of the axis message frames of the SINAMICS Control Unit.

This enables cyclic reading of the error code.

Summary of Contents for SIMOTION TM15




































































































Search results

Summary of Contents for SIMOTION TM15

Reviews:

Brands by name

Popular brands

Siemens SIMOTION TM15, Commissioning Manual

Search results

Summary of Contents for SIMOTION TM15

Reviews:

Brands by name

Popular brands