Siemens SIMOTION TM15 Commissioning Manual Download Page 58

Page: 58 / 99

Application tips

5.3 Power switches ("SmartFETs")

TM15 / TM17 High Feature Operating Manual

Commissioning Manual, 05/2009

5.3

Power switches ("SmartFETs")

The power switches used for outputs have built-in protection from excessive load currents

and short circuits at the output. The hardware of the module monitors the overcurrent/over

temperature signal.

Note
If the power switch is switched OFF due to an over temperature or overcurrent condition but

the "ON" command persists, the output will be switched on again once the over temperature

or overcurrent condition is eliminated.

The green channel LED illuminates when the power switch of the channel is switched on. A

diode at each output protects the power switch from a reverse overvoltage failure when an

inductive load is switched off.
You will find further information on handling inductive loads in our FAQs.

*UHHQ

&KDQQHO

/('

Summary of Contents for SIMOTION TM15




































































































Search results

Summary of Contents for SIMOTION TM15

Reviews:

Brands by name

Popular brands

Siemens SIMOTION TM15, Commissioning Manual

Search results

Summary of Contents for SIMOTION TM15

Reviews:

Brands by name

Popular brands