Siemens SIMOTION P320-4 E Page 92 Manual Download

Page: 92 / 166

LED

Meaning

State

Description

ERROR or L2
(SF PROFINET LED)

Off

SIMOTION P320-4 is working error-free.

Error

Red: Continuous

light

Bus error at the PROFINET interface.

Red: Flashes quick‐

ly
(2 Hz)

Erroneous configuration.

Red: Flashes quick‐

(5 Hz)

FAULT state

(only in combination with L1 und L3)

INIT

Red:

Flashes slowly

(0.5 Hz)

During the INIT process, the SF PROFINET LED is con‐

trolled by the boot loader.
The precise flashing behavior therefore cannot be de‐

termined and displayed.
In the INIT state, 0.5 Hz flashing is displayed in the SI‐

MOTION P State.
If no project has yet been loaded, 0.5 Hz flashing is also

displayed for the INIT, which, in this case, is also re‐

tained in the Running state.

MAINT or L3
(SF LED)

Off

SIMOTION P320-4 works error-free.

Error

Red

An event has occurred which needs to be acknowledged

(alarm, message, notification).

(See Diagnostics Guide)

Red:

Flashes slowly

(0.5 Hz)

License missing for licensed technology objects.
Carry out the licensing to correct the error.
Further information on the licensing can be found in the

SIMOTION P320-4 E / SIMOTION P320-4 S Commis‐

sioning and Hardware Installation Manual.

Red: Flashes quick‐

(5 Hz)

FAULT state
(only in combination with L1 and L2)
A fault has occurred to which the user program cannot

respond.
The following actions may be required to rectify the fault:
● Power OFF/ON
● Recommissioning

Interfaces
5.4 Status displays

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands