background image

6. If the contents of the packaging are incomplete, damaged or do not match your order, inform 

the responsible delivery service immediately. 

WARNING

Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or 

plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.
Make sure that the damaged device is not inadvertently installed and put into operation. 

Label the damaged device and keep it locked away. Send off the device for immediate 

repair.

NOTICE
Damage from condensation   
If the device is subjected to low temperatures or extreme fluctuations in temperature during 

transportation, for example in cold weather, moisture could build up on or inside the HMI 

device. 
Moisture can result in short-circuits in electrical circuits and damage the device.
In order to prevent damage to the device, proceed as follows:     
● Store the device in a dry place.
● Bring the device to room temperature before starting it up.
● Do not expose the device to direct heat radiation from a heating device.
● If condensation develops, wait approximately 12 hours or until the device is completely 

dry before switching it on.

7. Please keep the enclosed documentation, it belongs to the device. You need the 

documentation when you commission the device for the first time.

8. Write down the identification data of the device.

Application planning
4.1 Unpacking and checking the delivery

SIMOTION P320-4 E / P320-4 S

78

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Reviews: