Siemens SIMOTION P320-4 E Page 134 Manual Download

Page: 134 / 166

9.2

General technical specifications

General technical specifications for SIMOTION P320-4
Article numbers

SIMOTION P320-4 E
● 6AU1320-4DE65-3AF0
SIMOTION P320-4 S
● 6AU1320-4DS66-3AG0

Dimensions

262 × 133 × 50.5 (W × H × D in mm)

Weight

Approximately 2 kg

Supply voltage (DC)

24 VDC

(-20%/+20%)

Short-term voltage interruption in accord‐

ance with Namur

Min. 15 ms (at 20.4 V)

Max. 10 events/h; recovery time min. 1 s

Max. power consumption

64.8 W (at 24 V)

Degree of protection

IP 20 according to IEC 60529

Protection class

Protection class I according to IEC 61140

Safety regulations

EN 60950-1; UL 60950-1; UL 508;

Noise emission

<40dB (A) to DIN 45635-1

Quality assurance

In accordance with ISO 9001

The upstream power supply must generate a safety extra-low voltage with safe electrical

isolation according to IEC 60364-4-41 or an NEC Class 2 SELV and LPS according to IEC/

UL/EN/ DIN-EN 60950-1 (see the section "Connecting the power supply (24 V DC)

(Page 121)").

Electromagnetic compatibility

Electromagnetic compatibility
Interference emission

EN 61000-6-3, EN 61000-6-4, CISPR220 class B; FCC class A

Immunity with regard to conducted

interference on the supply lines

± 2 kV according to IEC 61000-4-4; burst

± 1 kV according to IEC 61000-4-5; symmetrical surge

± 2 kV according to IEC 61000-4-5; asymmetrical surge

Noise immunity on signal lines

± 1 kV according to IEC 61000-4-4; burst; length < 3 m

± 2 kV according to IEC 61000-4-4; burst; length > 3 m

± 2 kV according to IEC 61000-4-5; surge; length > 30 m

Immunity to electrostatic discharge ± 6 kV contact discharge according to IEC 61000-4-2

± 8 kV air discharge according to IEC 61000-4-2

Immunity to RF interference

10 V/m 80–1000 MHz and 1.4–2 GHz, 80% AM according to

IEC 61000-4-3

1 V/m 2–2.7 GHz, 80% AM according to IEC 61000-4-3

10 V 10 kHz to 80 MHz, 80% AM according to IEC 61000-4-6

Immunity to magnetic fields

100 A/m, 50/60 Hz according to IEC 61000-4-8

Technical data
9.2 General technical specifications

SIMOTION P320-4 E / P320-4 S

134

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands