Siemens SIMATIC NET RUGGEDCOM RST2228P Installation Manual Download Page 49

Page: 49 / 60

Technical Specifications
5.7 Mechanical Specifications

Ambient Operating

Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Storage Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

5% to 95%

Pollution Degree

PD2

Maximum Altitude

3000 m (9842 ft)

Measured from a 30 cm (11.8 in) radius surrounding the center of the enclosure.

Operating temperature may vary based on the limitations of installed SFPs. Refer to the

RUGGEDCOM

SFP Transceivers Catalog

for SFP temperature ratings.

Non-condensing.

5.7

Mechanical Specifications

Weight

8.0 kg (18 lbs)

Ingress Protection

IP3x (for pluggable connectors)

Enclosure

Galvanized steel

5.8

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

RUGGEDCOM RST2228P

Installation Manual, 07/2021, C79000-G8976-1403-13

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P





























































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228P

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RST2228P, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228P

Brands by name

Popular brands