manualshive.com logo in svg

Siemens SIMATIC NET RUGGEDCOM RST2228P, Installation Manual, Page: 37 / 60

Share
Download
Siemens SIMATIC NET RUGGEDCOM RST2228P Installation Manual Download Page 37

Device Management
3.2 Configuring the Device

USB Console Port

Connect a workstation directly to the USB Type-B console port to access the boot-

time control and RUGGEDCOM RST2228P interfaces. The console port provides

access to RUGGEDCOM RST2228P's console and Web interfaces.

NOTICE

Electrical Hazard – risk of temporary network packet corruption

Do not expose the USB console port to large static electric fields.

IMPORTANT

The USB console port is intended to be used for service of the device only, such as

initial configuration or troubleshooting. Management of the system during normal

operation must be done over Ethernet.

Note

For Microsoft Windows users, the RUGGEDCOM USB Serial Console driver must be

installed on the users workstation before connecting via the USB Type-B console port.

For more information, refer to the 

RUGGEDCOM ROS Configuration Manual

 for the

device.

Use the following settings to connect to the port:

Speed

57600 baud

Data Bits

8

Stop Bit

1

Parity

None

Flow Control

Off

Terminal ID

VT100

Ethernet Ports

Connect any of the available Ethernet ports on the device to a management

switch and access the RUGGEDCOM RST2228P console and Web interfaces via the

device's IP address. The factory default IP address for the RUGGEDCOM RST2228P is

https://192.168.0.1

.

For more information about available ports, refer to 

"

Communication Ports

 (Page

33)"

.

Note

Single-mode fiber ports only support Ultra Physical Contact (UPC) cable connectors.

3.2

Configuring the Device

Once the device is installed and connected to the network, it must be configured.

All configuration management is done via the RUGGEDCOM RST2228P interface.

28

RUGGEDCOM RST2228P

Installation Manual, 07/2021, C79000-G8976-1403-13

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P





























































Reviews:

No comments