Siemens Simatic ET 200pro FC Operating Instructions Manual Download Page 136

Page: 136 / 196

Series commissioning and operation

8.1 Transfer of the frequency converter parameter assignment

ET 200pro FC

136

Operating Instructions, 07/2016, A5E01100763B AC

8.1.4

Parameter transfer with PC (STARTER)

Upload from frequency converter to the PC

Parameters are uploaded from the frequency converter's RAM to a project file on a PC's

hard disk using STARTER. STARTER can be connected via a fieldbus or directly to the

frequency converter's RS232 interface.
Prerequisites

●

You must have a converter with a suitable parameter set at your disposal (upload

converter).

●

STARTER must be installed on the PC used for standard commissioning.

●

The upload converter's power supply must be connected.

●

The upload converter is in the "Ready to run" state.

Connect the STARTER PC to the upload frequency converter via RS232 (point-to-point
connection, appropriate connecting cable required) or via fieldbus, press the online button

("Connect to target system") and perform the upload using the button.

Remark
An online connection can only be established between the PC and frequency converter via

fieldbus if the following conditions are met:

●

The interface module of the ET 200 station is running in DPV1 mode.

●

There is no CPU between the PC and the frequency converter (also applies to the

Download from PC to the frequency converter

In the case of a manual download, all parameters (with the exception of fail-safe parameters)

will be transferred to the frequency converter.

Summary of Contents for Simatic ET 200pro FC





































































































































































































Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands

Siemens Simatic ET 200pro FC, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands