manualshive.com logo in svg

Siemens POLYMOBIL Plus, Service Instructions Manual, Page: 5 / 50

Share
Download
Siemens POLYMOBIL Plus Service Instructions Manual Download Page 5

1 - 1

Siemens AG

 

SPR8-125.061.02

Page 1 of 4

POLYMOBIL Plus

Medical Engineering

Rev. 01

01.00

TD SD 24

 

 

Prerequisites

1

Text emphasis

1

Required documents

1

Tools, measurement and auxiliary devices required

1

The tools, measurement and auxiliary devices required, with the exception of the standard 
service equipment and the current transformer, are listed in part 3 of the ARTD.

"Warnings" are information provided with special emphasis when 
there is the potential for personal injury to the operator or patient.

"Cautions" are information provided with special emphasis when 
there is the potential for damage to the equipment.

"Notices" are information provided with special emphasis to facil-
itate proper use of the equipment or proper execution of a proce-
dure.

•

Block circuit diagram

X 069I

•

Function description

SPR8-125.041.01...

A detailed circuit diagram, DIN A 3, can be ordered under item
number 18 20 377 X069I.

•

Standard service kit

•

Digital multimeter

•

2-channel memory oscilloscope

•

mAs meter

•

Protective conductor meter

•

 Equivalent leakage current meter

•

Torque wrench 20 Nm - 100 Nm

•

Loctite 242

•

Current transformer (50 A : 50 mA) 
with 10 Ohm; 0.5 W; 1% metal film resistor
Refer also to Speed Info 06/91

(31 51 289 B2716)
(10 14 984 B0512)

The oscilloscope has to be connected to ground to perform mea-
surements. A TEK video isolator and the trigger set have to be 
used when ground loops may distort the measurement results.

WARNING

CAUTION

NOTICE

NOTE

CAUTION

Summary of Contents for POLYMOBIL Plus



















































Reviews:

No comments