manualshive.com logo in svg

Siemens POLYMOBIL Plus, Service Instructions Manual, Page: 20 / 50

Share
Download
Siemens POLYMOBIL Plus Service Instructions Manual Download Page 20

POLYMOBIL Plus

 

SPR8-125.061.02

Page 4 of 4

Siemens AG

 

Rev. 01

01.00

TD SD 24

Medical Engineering

3 - 4

Troubleshooting

 

Err 17

Maximum exposure time (Max. exposure time reached)

- Filament current too low?
- mAs counter is set incorrectly (P1 on D915)?

Err 18

Exposure not completed (exposure not completed by the system - expo-
sure switch was released)

- Operator error?
- Intermittent contact in the release switch?
- Error in the exposure release circuit?

Err 20

Capacitor bank not ready

Device was not ready yet / had not released yet.

- F1 on D950 defect?
- Error on D950?

Err 21

Vfil > Vmax (Max. Filament heating exceeded during preparation)

- Error during the acquisition of the filament heating?
- Basic value of the exposure filament incorrectly set (P5 on D915)?
- Error on D915?

Err 22

Maximum preparation (preparation time too long)

- Prep level pressed too long.

Err 30

Fast capacitor charge (capacitor bank charges too fast)

- Are all fuses on the capacitor bank (D970) ok?
- Are there defective capacitors?
- Is the line voltage too high (> 250 V)?
- Is the charging frequency too high?
- Configure the capacitor bank.
- D950 defect?

Err 31

Slow capacitor charge (capacitor bank charges too slow

)

- ’V25’ (line) on D950 flashing? Check fuse F1
- None or insufficient charging frequency?
- Check D950 (’V22 - V24’ defective?)
- Poor connections to / in the capacitor bank?

Err 33

Inverter Error

- Check ribbon cable X20.
- FMAX not adusted?
- IGBT short - circuited?

Err 34

Filament Inverter short - circuit

- FMAX not adjusted?
- IGBT short - circuited?

Err 90

EPROM checksum

- EPROM defective.

Err 96

kVnom failure (hardware error , refer also to Err 5)

Err 97

mAnom failure (hardware error, refer also to Err 6)

Summary of Contents for POLYMOBIL Plus



















































Reviews:

No comments