Siemens OPTIPOINT 500 Service Manual Download Page 87

Page: 87 / 120

P31003-E8400-A100-3-7620
Service Manual

7-23

Nur für den internen Gebrauch

IP Adapter

Administration via optiPoint 500

Figure 7-5

Faults shown on optiPoint display

Once a fault occurs, press any key on the terminal to open the optiPoint IPadapter administra-
tion menu. You can resolve the fault there by modifying the appropriate settings.

If a parameter is invalid or not set correctly, the following error messages are also displayed for
the configuration setting:

’CFG error Oxnnnn’

Example:

If an invalid Partner_IP address is entered or if the partner IP address is not set, the following
error code appears: ’

0x1000

’ (see figure below)

NO DHCP response
Press any key? >

Ping to Gateway failed
Press any key? >

Ping to Partner failed
Press any key? >

highest priority

lowest priority

Generic socket error
Press any key? >

TC Login Error
Press any key? >

Error connecting partner
Press any key? >

Unknown Error
Press any key? >

Summary of Contents for OPTIPOINT 500

























































































































Search results

Summary of Contents for OPTIPOINT 500

Reviews:

Related manuals for OPTIPOINT 500

Brands by name

Popular brands

Siemens OPTIPOINT 500, Service Manual

Search results

Summary of Contents for OPTIPOINT 500

Reviews:

Related manuals for OPTIPOINT 500

Brands by name

Popular brands