Siemens OPTIPOINT 500 Service Manual Download Page 52

Page: 52 / 120

Option Adapters and Ports

Nur für den internen Gebrauch

P31003-E8400-A100-3-7620

5-6

Service Manual

optiPoint 500 acoustic adapter

Desk Microphone:

Pin assignment Headset: MW 8/8

The electrical values comply with FTZ 121TR9-5.

Pin assignment Floating contact: MW6/6

5.2.1

Electrical Requirements of the Headset

Input level -50 dBm:

-12 dBm PCM signal

Input resistance:

150k parallel with 220 nF in series with 36K

Sense lead to GND:

Internal microphone deactivated

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

GND

TX_AUD

RX_AUD

TX_AUD

RX_BUS

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

ACT1

RING

ACT2

●

The electrical values comply with FTZ 121TR9-5

●

Audio transmission from one headset is routed to the other headset (recommended
by Plantronics).

●

The way in which this option interacts with the telephone and the CS is described by
the CorNet-TS layer 3 specification for Symphony.
The CS can detect a headset after it has been plugged into this option.

●

Microphone (Elektret interface):

Max. current:

≤

400

Supply voltage:

5 V

10%

Series resistance:

5 k

Ω

±10%

●

Audio converter:

Impedance:

150

Ω

±10%

EBD:

13 dB±2.5dB

Summary of Contents for OPTIPOINT 500

























































































































Search results

Summary of Contents for OPTIPOINT 500

Reviews:

Related manuals for OPTIPOINT 500

Brands by name

Popular brands

Siemens OPTIPOINT 500, Service Manual

Search results

Summary of Contents for OPTIPOINT 500

Reviews:

Related manuals for OPTIPOINT 500

Brands by name

Popular brands