5 System Parameters
International English
MICROMASTER 440 Operating instructions
64
6SE6400-5CA00-0BP0
Alarms, Warnings and Monitoring (P0004 = 21)
Par. No.
Parametername
Default
Acc
WS
QC
r0947[8]
Last fault code
-
2
-
-
r0948[12]
Fault time
-
3
-
-
P0952
Total number of faults
0
3
CT
N
P2100[3]
Alarm number selection
0
3
CT
N
P2101[3]
Stop reaction value
0
3
CT
N
r2110[4]
Warning number
-
2
-
-
P2111
Total number of warnings
0
3
CT
N
r2114[2]
Run time counter
-
3
-
-
P2115[3]
AOP real time clock
0
3
CT
N
P2150[3]
Hysteresis frequency f_hys
3.00
3
CUT
N
P2151[3]
CI: Monitoring speed setpoint
0:0
3
CUT
N
P2152[3]
CI: Act. monitoring speed
0:0
3
CUT
N
P2153[3]
Time-constant speed filter
5
2
CUT
N
P2155[3]
Threshold frequency f_1
30.00
3
CUT
N
P2156[3]
Delay time of threshold freq f_1
10
3
CUT
N
P2157[3]
Threshold frequency f_2
30.00
2
CUT
N
P2158[3]
Delay time of threshold freq f_2
10
2
CUT
N
P2159[3]
Threshold frequency f_3
30.00
2
CUT
N
P2160[3]
Delay time of threshold freq f_3
10
2
CUT
N
P2161[3]
Min. threshold for freq. setp.
3.00
2
CUT
N
P2162[3]
Hysteresis freq. for overspeed
20.00
2
CUT
N
P2163[3]
Entry freq. for perm. deviation
3.00
2
CUT
N
P2164[3]
Hysteresis frequency deviation
3.00
3
CUT
N
P2165[3]
Delay time permitted deviation
10
2
CUT
N
P2166[3]
Delay time ramp up completed
10
2
CUT
N
P2167[3]
Switch-off frequency f_off
1.00
3
CUT
N
P2168[3]
Delay time T_off
10
3
CUT
N
r2169
CO: Act. filtered frequency
-
2
-
-
P2170[3]
Threshold current I_thresh
100.0
3
CUT
N
P2171[3]
Delay time current
10
3
CUT
N
P2172[3]
Threshold DC-link voltage
800
3
CUT
N
P2173[3]
Delay time DC-link voltage
10
3
CUT
N
P2174[3]
Torque threshold T_thresh
5.13
2
CUT
N
P2176[3]
Delay time for torque threshold
10
2
CUT
N
P2177[3]
Delay time for motor is blocked
10
2
CUT
N
P2178[3]
Delay time for motor is stalled
10
2
CUT
N
P2179
Current limit for no load ident.
3.0
3
CUT
N
P2180
Delay time for no load ident.
2000
3
CUT
N
P2181[3]
Belt failure detection mode
0
2
CT
N
P2182[3]
Belt threshold frequency 1
5.00
3
CUT
N
P2183[3]
Belt threshold frequency 2
30.00
2
CUT
N
P2184[3]
Belt threshold frequency 3
50.00
2
CUT
N
P2185[3]
Upper torque threshold 1
99999.0
2
CUT
N
P2186[3]
Lower torque threshold 1
0.0
2
CUT
N
http://nicontrols.com
