manualshive.com logo in svg

Siemens LITHOSTAR Multiline SP, Start-Up Instructions

The Siemens LITHOSTAR Multiline SP is a cutting-edge medical product that ensures precision and efficiency in lithotripsy procedures. To get started with this advanced device, simply access our website and download the detailed Start-Up Instructions manual for free. Experience seamless usability and optimal results with Siemens LITHOSTAR Multiline SP.

Share
Download
background image

LITHOSTAR Multiline

 

RXL2-120.815.01

Page 4 of 4

Siemens AG

System manual

Rev. 02

02.05

CS PS 24

Medical Solutions

2 - 4

General Start-Up

 

Systems with the ultrasound option:

•

Remove the front cover (Fig. 2).

•

Install the uro insert.

•

Move the unit to the left so that board D31 is accessible.

•

Connect control cable X28 on board D31 and secure it with screws.

•

Reattach the cover.

Summary of Contents for LITHOSTAR Multiline SP























































Reviews:

No comments

Related manuals for LITHOSTAR Multiline SP

DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
OMCA 760 Use And Maintenance Manual preview
760
Brand: OMCA Pages: 36
Salford 699 Assembly And Parts Manual preview
699
Brand: Salford Pages: 64
VeEX FX30 Quick Manual preview
FX30
Brand: VeEX Pages: 2
JB-Lighting P8 Operating Instructions Manual preview
P8
Brand: JB-Lighting Pages: 48
Zenbooth Duo Build Instructions preview
Duo
Brand: Zenbooth Pages: 60
JB-Lighting P4 Operating Instructions Manual preview
P4
Brand: JB-Lighting Pages: 60
Banfer Vario Manual preview
Vario
Brand: Banfer Pages: 6
Hammer FR Series Operation And Maintenance Manual preview
FR Series
Brand: Hammer Pages: 42
GE Optima XR200amx Preinstallation Manual preview
Optima XR200amx
Brand: GE Pages: 46
SCHUNK PFH 30 Repair Instructions preview
PFH 30
Brand: SCHUNK Pages: 2
Frick IDSC Installation Operation & Maintenance preview
IDSC
Brand: Frick Pages: 36
SDE Lighting Sixty Scan Manual preview
Sixty Scan
Brand: SDE Lighting Pages: 7
Eaton AtLite Sure-Lites SELDWA29SD Installation Instructions preview
AtLite Sure-Lites SELDWA29SD
Brand: Eaton Pages: 4

Brands by name

Popular brands

Load more brands