Siemens LITHOSTAR Multiline SP Start-Up Instructions Download Page 51 | Manualshive

Page: 51 / 54

background image

8 - 1

Siemens AG

RXL2-120.815.01

Page 1 of 2

LITHOSTAR Multiline

Medical Solutions

Rev. 02

02.05

CS PS 24

System manual

Final Steps

8

Customer-specific and Country-specific Settings for the Multiline

8

Set requested language according to instruction RXL2-120.032... "Service Software Soft-
ware parameter/monitoring". Parameter Group: / Configuration: User terminal.

Set clinic name according to instruction RXL2-120.032... "Service Software Software
parameter/monitoring. Parameter Group: / Clinic data.

Correct the date and time in the host computer D1 according to instruction "Operation of
the service software" RXL2-120.113...

Back-up and Error Memory

8

•

Perform a back-up and then erase the error memory in the generator and in the Multiline
(refer to Service Software Instructions, RXL2-120.034... and RXL2-120.113...) after
concluding the start-up.

Final Steps

8

•

If the shielding panels have been removed, reinstall them.

•

Attach the labels from register 9 (system binder) at appropriate locations.

•

Install all cover plates, except for the generator front panel and connect the protective
conductors.

•

Measure the protective conductor resistance.

The input field "Actual:" is filled with blanks. These are not visible.
All banks must be deleted before entering the clinic name.

Test meter:

Protective conductor meter

Measurement
value:

max. 0.2 Ohm

(observe country-specific regulations)
(Current 10 A, voltage drop max. 2 V)

Test procedure:

The measurement is made between all conductive parts accessible to
the user and the protective conductor rail in the generator.

Conditions:

Protective conductor resistance: max. 0.2 Ohm

•

If it is greater than this value, increase the wire gauge of the
protective conductor.

•

Reduce the transfer resistance (e.g. tighten the screws).

NOTICE

Unit
Monitor
Cabinets
I.I.
X-ray tube
Collimator
etc.

Prot. conductor meter

≤

0.2 Ohm

Generator

«
...
49
50
51
52
53
...
»

Summary of Contents for LITHOSTAR Multiline SP























































Reviews:

No comments

Related manuals for LITHOSTAR Multiline SP

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Eagle Pages: 3

Brand: Modulate Pages: 2

Brand: Dairyland Pages: 21

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: M-system Pages: 3

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: Tanco Pages: 112

Brand: MAKSIWA Pages: 155

Brand: VanGaa Lighting Pages: 7

GPSMAP 7400 Series

Brand: Garmin Pages: 8

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

SimNewB Anomaly Set

Brand: laerdal Pages: 10

Brand: Life Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands