Siemens LITHOSTAR Multiline SP Start-Up Instructions Download Page 6 | Manualshive

Page: 6 / 54

background image

LITHOSTAR Multiline

RXL2-120.815.01

Page 2 of 6

Siemens AG

System manual

Rev. 02

02.05

CS PS 24

Medical Solutions

1 - 2

Prerequisites / General Information

Important Information Regarding Start-Up

1

The system cabling must be complete.

The system has been preassembled to system level, programmed and also tested at the
factory (see test certificates for generator, unit and image quality measurement, filed in
the system binder). During start-up, only a few checks or tests are required to ensure that
none of the settings has changed.

The results for tests marked must be entered in the test certificate or the image quality
test protocol as indicated for the specific case.

The following tests required for the acceptance test in the Federal Republic of Germany
according to the X-Ray Ordinance, §16, or the acceptance test in the USA, were already
performed and are documented in the test certificates:

According to DHHS Regulations, the following items must be checked:

1.

Documents required for the customer

2.

Radiation protection

3.

DHHS and identification labels

Abbreviations and Symbols Used in these Instructions

1

When performing service work and tests, adhere to the product-
specific safety information in the document as well as the general
safety information contained in the ARTD/ Part 2.

The oscilloscope must always be connected to ground. Use the
TEK isolation transformer and the trigger option to avoid interfer-
ence from ground loops that may distort the measurement
results.

- Visual inspection of filter values

- Alignment of radiation field and film center

- Collimation of fluoroscopic field

- Centering of radiation field to center of monitor

- Fluoroscopy dose rate

- Maximum skin dose rate

- Resolution and minimum contrast

- Unit attenuation factor

- Check of kV accuracy

These measurement values and the values determined during the
start-up procedure can be taken from the test certificate and
entered in the Acceptance Test Protocol.

AH

= Recessed Allen screws

HH = Hex-head bolts

DVM

= Digital Volt Meter

SID = Source-to-image distance

FID

= Focus - Image Intensifier Distance

C

= Collimator

I.I.

= Image Intensifier

FL

= Fluoroscopy

NOTICE

NOTE

p

NOTE

«
...
4
5
6
7
8
...
»

Summary of Contents for LITHOSTAR Multiline SP























































Reviews:

No comments

Related manuals for LITHOSTAR Multiline SP

Brand: Malmet Pages: 14

Brand: Zempire Pages: 2

Brand: Bang & Olufsen Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 20

Brand: Eaton Pages: 24

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brand: iHealth Pages: 8

Contrology Cadillac

Brand: Balanced Body Pages: 7

Brand: Zodiac Pages: 2

Brand: Zimmer Pages: 46

Brand: Opvimus Pages: 50

Brand: Aspect Medical Systems Pages: 104

Brand: Hupfer Pages: 153

Brand: SAC Pages: 2

Brand: Life Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands