Siemens LDS 6 Operating Instructions Manual Download Page 77

Page: 77 / 102

LDS 6
Operating Instructions, 01/2009, A5E00295894-05

Spare Parts List

7.1

Compatibility of detectors with central units

For all gases except O

, LDS6 exists in two versions as a consequence of a major upgrade.

Three of the LDS6 spare parts are affected by the change and will consequently exist in two

different versions. The "Sensor electronic" spare parts consist of one detector and one

detector PCB (A5E00681433) respectively. The PCB is not affected by the modification but

the detector is different. This spare parts list corresponds to the technical state of February

2009.

7.1.1

Detector Labels

The detector A5E-number indicates if a sensor is to be used with a Version 2 central unit.

Besides the example in the following picture also A5E1033996 (HCl) and A5E1030124 (CD

6C) are used with version 2.
The detector revision number (e.g. ES01) is only important if selecting a spare part that has

been stored for some time. To avoid degraded performance, do not use a spare part with a

lower revision number to replace a detector with higher revision number.

Figure 7-1

Labeling on the detector unit

Summary of Contents for LDS 6







































































































Search results

Summary of Contents for LDS 6

Reviews:

Siemens LDS 6, Operating Instructions Manual, Page: 77 / 102

Search results

Summary of Contents for LDS 6

Reviews: