manualshive.com logo in svg

Siemens LDS 6, Operating Instructions Manual, Page: 49 / 102

Share
Download
Siemens LDS 6 Operating Instructions Manual Download Page 49

 

Operation 

 

4.3 Analyzer Functions 

LDS 6 
Operating Instructions, 01/2009, A5E00295894-05 

49

 

4.3.2

 

Analyzer Status 

Table 4- 3 

   

4 Display Meas. Range

3 Logbook

2 Diagnostics Values

1 Analyzer Configuration

Analyzer Status    Ch1 NH

3

 

This display appears when pressing the first soft key ("Analyzer Status"), following the 

selection of the diagnostics functions in the main menu. 
The status functions are freely-accessible. You will not be asked to enter a password. 

 

 

1 Analyzer Configuration 

1 Analyzer Config. Ch1 NH

3

 CE Drv.Software

 1 .0 .314

 CE Software

 3 .0 .126

 OS Version

 60001

 Serial No.

 7MBXXXXXXXXXXXXXXXXX

 Order No. 

...Continue

  

X

 2 .3  .245

 23

 Software Package Version

 

You can use this function to display important manufacturing data of the analyzer. 

●  Ordering No: Information on ordering data of analyzer. 
●  Serial No: Consecutive number of analyzer. 
●  Software Package Version: Version number of the application-specific configuration 

software. 

●  OS Version: Version number of the Windows CE operative system running in the 

analyzer. 

●  CE Software: Version number of the LDS 6-specific software. 
●  CE Driver Software: Version number of the driver software. 
●  Analyzer uC Drv.Software: Version number of the software running on the main micro 

controller. 

●  Channel uC Drv.Software: Version number of the software running on the measurement 

channel micro controller. 

●  Opto uC Drv.Software: Version number of the software running on the opto module micro 

controller. 

●  Chan. FPGA Firmware: Version number of the firmware running on the measurement 

channel FPGA. 

●  Opto. FPGA Firmware: Version number of the firmware running on the laser controller 

FPGA. 

●  Ref. FPGA Firmware: Version number of the firmware running on the reference channel 

FPGA. 

Summary of Contents for LDS 6







































































































Reviews:

No comments