Siemens LDS 6 Operating Instructions Manual Download Page 75

Page: 75 / 102

Maintenance and Service

6.7 Reconfiguration of the Path Length

LDS 6
Operating Instructions, 01/2009, A5E00295894-05

6.7

Reconfiguration of the Path Length

Starting from "Measuring window", press the soft key next to the component for which

you want to change the path length. Press the soft key for "Configuration". Enter the

password for privilege level 2 (the password is factory-set to the value "222", but may

have been replaced by a new one). Press "Continue" twice and then select function 84

"Path Length".

Press first soft key to edit the path length. Enter the new path length and press ENTER.

Press MEAS to return to measurement screen. Press MEAS again to loose privileges.

The procedure has to be repeated for other channels. It is not necessary to repeat the

procedure for more than one component per channel since this function is a channel-

specific function.

Summary of Contents for LDS 6







































































































Search results

Summary of Contents for LDS 6

Reviews:

Siemens LDS 6, Operating Instructions Manual, Page: 75 / 102

Search results

Summary of Contents for LDS 6

Reviews: