Siemens LDS 6 Operating Instructions Manual Download Page 68

Page: 68 / 102

Alarms

5.3 Faults Alarm

LDS 6

Operating Instructions, 01/2009, A5E00295894-05

5.3

Faults Alarm

Any faults in the hardware that makes the analyzer unable to carry out measurements, result

in a "fault alarm". The measured value flashes, and then it is always necessary to take

corrective measures.
The faults listed in the following table lead to a fault alarm message in the logbook. These

can be individually deactivated by using function 88.

Table 5- 3

Fault alarm messages

No.

Error Message

Possible Causes

Action

Opto module

Laser damage.

Leaking reference cell.

Reference cell displacement.

Electronics damage.

Contact service.

Laser Current

Change of laser current due to ageing of laser.

Contact service.

Signal Quality

Signal amplitude too high due to high component

concentration.

Contact service.

Signal amplitude too low when measuring

temperature.

Contact service.

External Fault

External signaling.

Check external equipment.

Supply Voltage Channel

Internal power failure.

Contact service.

Supply Voltage Analyzer Internal power failure.

Contact service.

Serial EEProm

Internal EEProm failure.

Contact service.

S11

FPGA Channel

Electronics failure in data acquisition unit.

Contact service.

S12

CAN Analyzer

Electronics failure in internal communication.

Contact service.

S13

CAN Channel

Electronics failure in internal communication.

Contact service.

S14

Data Flow Analyzer

Electronics failure in internal communication.

Contact service.

Summary of Contents for LDS 6







































































































Search results

Summary of Contents for LDS 6

Reviews:

Siemens LDS 6, Operating Instructions Manual, Page: 68 / 102

Search results

Summary of Contents for LDS 6

Reviews: