background image

76

Using several handsets

Gigaset S450 IP LBA / IM-Nord_en / A31008-M1713-R221-2-7619 / T-NetBox_SAG-registration.fm / 28.3.07

Ve

rs

ion 4,

 16

.09.

2005

Using a handset as a room 
monitor

If the room monitor is activated, a previ-

ously stored destination number is called 

as soon as a set noise level is reached in 

the room. 
You can store an internal or external 

number in your handset as the destination 

number. 
The room monitor call to an external 

number stops after around 90 seconds. 

The room monitor call to an internal 

number (handset) stops after around 

3 minutes (depending on the base 

station). During use as a room monitor, 

all keys are barred except for the end call 

key 

a

. The speaker of the handset is 

muted. The end call key can only be used 

to deactivate the handset.
When the room monitor is activated, 

incoming calls to the handset are indi-

cated 

without a ringer tone

 and are only 

shown on the screen. The display and 

keypad are not illuminated and advisory 

tones are also turned off.
If you accept an incoming call, the room 

monitor mode is suspended for the dura-

tion of the call, but the function 

remains

 

activated.
If you switch off the handset, the room 

monitor mode is deactivated. You must 

reactivate the function when you switch 

the handset back on. 

Activating the room monitor and 

entering the number to be called

v

  

¢

í

Add. Features 

¢

Room Monitor 

¤

Change multiple line input: 

Room M.:

Select 

On

 to activate.

Call to:

Press the display key 

§Edit§

 and enter des-

tination number.

External number:

 Select number from 

the directory or enter directly. Only 

the 

last 4 characters

 are displayed.

Internal number:

 Delete any stored 

external number. 

§INT§

s

 (select hand-

set or 

Call All

, if all registered handsets 

are to be called)

§OK§

.

Store number with 

Save

.

Level:

Set noise level sensitivity (

Low

 or 

High

).

¤

Save changes (page 112).

The function is now activated. With 

v

you can move directly to settings.

Caution!

You should always check the operation 

of the room monitor before use. For 

example, test its sensitivity. Check the 

connection if you are diverting the room 

monitor to an outside number.

 

– When the function is switched on the hand-

set's operating time is severely reduced. If 

necessary, place the handset on the base 

station. This ensures that the batteries do 

not run down.

– Ideally the handset should be positioned 1 

to 2 metres away from the baby. The micro-

phone must be directed towards the baby. 

– The connection to which the room monitor 

is diverted must not be blocked by an acti-

vated answer machine.

Please note: 

An external number will be dialled via the set 

standard connection (VoIP or fixed network). 

If the number is to be dialled via the non-

standard connection, enter a star (*) at the 

end of the number. 

Summary of Contents for Gigaset S450 IP
















































































































































Reviews: