Siemens Gigaset S450 IP User Manual Download Page 104

Page: 104 / 143

103

Appendix

Gigaset S450 IP LBA / IM-Nord_en / A31008-M1713-R221-2-7619 / appendix.fm / 28.3.07

ion 4,

.09.

2005

Base Search

flashes in the display.

The handset is set to

Best Base

and no base sta-

tion is switched on or within range.

Move the handset closer to the base sta-

tion.

Check the base station mains adapter.

Please register

flashes in the display.

The handset is not registered.

Handset does not ring.

The ringer tone is switched off.

Activate the ringer tone (page 62).

You cannot hear a ring/dialling tone from

the fixed network.

Base station's phone cord has been replaced.

When purchasing a new cord, ensure that it

has the correct pin connections (page 11).

The other party cannot hear you.

You have pressed the

(INT) key. The hand-

set is "muted".

Switch on the microphone again (page 23).

When making calls from the fixed network,

the caller's phone number is not displayed

although CLIP (page 22) is set.

Phone number identification is not enabled.

The

caller

should ask his network provider

to enable Calling Line Identification (CLI).

You hear an error tone when keying an

input

(a descending tone sequence).
Action has failed/invalid input.

Repeat the operation.
Watch the display and refer to the user

guide if necessary.

You cannot connect to the router and the

phone is assigned a static IP address.

Check on the router whether the IP address

is already being used by another device in

the LAN or belongs to the block of IP

addresses that is reserved on the router for

dynamic address assignment.

If necessary, change the phone's IP address

(page 68).

You have made a call via VoIP but cannot

hear the other participant

Your phone is connected to a router with NAT/

firewall.

Your STUN server (page 87) or outbound

proxy (page 88) settings are incomplete or

incorrect. Check the settings.

No outbound proxy is entered or the out-

bound proxy mode

Never

is activated

(page 88) and your phone is connected to a

router with symmetric NAT or a blocking

firewall.

Port forwarding is activated on your router,

but no permanent IP address has been

assigned to your phone.

You cannot make calls via VoIP

Server not

accessible!

is displayed.

First wait a few minutes. This is often a

short-term event that corrects itself after a

short time.

If the message is still displayed, proceed as fol-

lows:

Check whether your phone's Ethernet cable

is correctly connected to the router.

Check your router's cable connection to the

Internet.

Check whether the phone is connected to

the LAN. Set a ping command, for example,

on the phone (ping

<local IP address of

the phone>). It may be that no IP address

could be assigned to the phone or a perma-

nently set IP address is already assigned to

another LAN subscriber. Check the settings

on the router, you may have to activate the

DHCP server.

Summary of Contents for Gigaset S450 IP
















































































































































Search results

Summary of Contents for Gigaset S450 IP

Reviews:

Related manuals for Gigaset S450 IP

Brands by name

Popular brands

Siemens Gigaset S450 IP, User Manual

Search results

Summary of Contents for Gigaset S450 IP

Reviews:

Related manuals for Gigaset S450 IP

Brands by name

Popular brands