Siemens Climatix Series Basis Document Download Page 178

Page: 178 / 244

178 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

HMI

01.02.2010

17.4 Main overview

Diese Seite enthält eine Übersicht aller Hauptwerte der konfigurierten Applikation.

17.5 Configuration

Write access 4 required to go to this page.

Main Index > Configuration

Parameter

Function

Value range

Unit

Standard R

S Link

Configuration by

Choose the way of configuration

HMI Config

Download

Configuration 1

Indicator if Configuration 1 is finished.

Jumpline to Configuration 1

NotDone

Done

Configuration 2

Indicator if Configuration 2 is finished.

Jumpline to Configuration 2

NotDone

Done

Configuration IO’s

Indicator if Configuration IO’s is finished.

Jumpline to the IO Configuration

NotDone

Done

Section:

Check Config IO’s

Jumpline to the IO check

Doubled

If you have configured one In or Output more

than once, you get a Fault

OK.

Fault

Not Configured

If you have configured a function, and not

configured the needed IO’s you get a Fault.

OK.

Fault

Integrations

Jumpline to the configuration of the

communication

RoomUnit1

Jumpline to room Unit 1 (not implemented)

RoomUnit2

Jumpline to room Unit 2 (not implemented)

17.6 Configuration 1

Write access 4 required to go to this page.

Main Index > Configuration > Configuration 1 --- General

Parameter

Function

Value range

Unit

Standard R

S Link

Extension modules

Number of extension modules

One

Two

Fire alarm

Kind of Fire alarm

alarm = digital Input for alarm

tmp = Supply /Exhaust Temperatur are

supervised

alarm+tmp = both variants are active

alarm

tmp

alarm+tmp

Filter alarm

Existing Filter alarms

Combined = one alarminput for both Filters

Supply = only Supply Filter

Exhaust = only Exhaust Filter

Sply+Exh = both Filter with separate Inputs

Combined

Supply

Exhaust

Emergency stop

Digital Input Emergency stop

Yes

alarm ackn input

Digital Input for Alarm ackn button Button

Yes

Su/Wi input

Digital Input for Summer Winter Change over

TRUE = Summer

Yes

4 Section:

TSP function

Select the needed Scheduler function

No = Scheduler disabled

Step = possible OpMode Off / [Number of

Steps selected in TSP Steps]

Step+tmp = possible OpMode Off/ [Number

os Modes selected in TSP Steps]

Step

Step+tmp

Step

TSP Steps

If TSP function = Step: Number of Steps for

Fan

If Tsp Functon = Step+Temp: Number of

Setpoints (Off /Eco1-3 /Com1-3)

1Step

2Steps

3Steps

1St

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 178

Summary of Contents for Climatix Series





















































































































































































































































Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands

Siemens Climatix Series, Basis Document

Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands