Siemens Climatix Series Basis Document Download Page 126

Page: 126 / 244

126 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Communication

01.02.2010

Proceed as follows to configure the LON module and connect to the LON bus:

Step Action

Controller

OFF

Connect LON module to controller using plug connection.

Connect LON bus cable to LON module (connections CLA and CLB).

Controller



The module starts / initialization begins.



Communication with the controller and LON bus is active as soon as

the two LEDs "BSP" and "BUS" are steady green.

Caution:

HMI must be reset a second time to update; prior to parame-

terization.

The LON card is operational and communicating with the LON network

when both LEDs are green.

"Generate" a new account in the LON tool (e.g. NL220, LON Maker).

Press service pin on the LON module:



The module is recognized and displayed in the LON tool.



All network variable are available.

Issue logical address via the LON tool.

Bind the network variable (or use the system integrator via the LON

tool).

After successful LON commissioning via the LON tool, you can access the control-

ler via the LON bus using Saphir Scope.

Main Index > System overview > Communication > Comm module overview >

Module[x] LON

Parameter

Range

Function

State

−

OK.

−

Alarm

Module state.

Comm failure

−

Passive

−

Active

Communication error between module and con-

troller. (e.g. no LON application loaded on the

Neuron Chip).

Location

Displays information that can be set via the LON

chip during bus commissioning.

Application

Name of loaded LON application (list of LON

variable) on the Neuron chip.

Neuron ID

Displays ID number for the Neuron chips.

Send heart beat

Displays current interval for sending values.

Receive heart beat

Displays current interval for receiving values.

Min send intervall

Displays current minimum interval for sending

values. A value may only be sent a maximum of

one time during this interval.

Settings

Go to settings page to parameterize LON mod-

ule.

Software version

Module software version.

Device ID.

Module hardware ID.

Commission LON

module

Note

Parameter

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 126

Summary of Contents for Climatix Series





















































































































































































































































Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands

Siemens Climatix Series, Basis Document

Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands