Siemens Climatix Series Basis Document Download Page 166

Page: 166 / 244

166 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Configuration

01.02.2010

Parameter

Range

Function

Cooling 2 pump

No additional water cooling pump.

Yes

Water cooling pump without pump kick. Digital output for the pump.

Yes+Kick

Water cooling pump with pump kick. A digital output for pump and ac-

tivation of pump kick.

Pump kick: Pump is switched on for a short period after idling for a

longer period. This prevents lock up.

Cooling 2 pump alm No

Pump without alarm or feedback.

Alarm

Pump with alarm. Digital input for pump alarm. Logical 1 = alarm, im-

mediately shuts down the pump.

Fdbk

Pump with feedback. Digital input for feedback (logical 1 = Pump running).

Both

Pump with alarm and feedback. Two digital inputs for pump alarm and

feedback.

Cooling 2 Dx alarm No

Additional direct expansion evaporator without alarm or feedback.

Alarm

Direct expansion evaporator with alarm. Digital input for pump alarm.

Logical 1 = alarm, immediately shuts down the pump.

Fdbk

Direct expansion evaporator with feedback. Digital input for feedback

is enabled (logical 1 = Pump running).

Both

Direct expansion evaporator with alarm and feedback. Two digital in-

puts for alarm and feedback.

Cooling 2 control

Positioning of additional cooling register.

StandAlone

Cooling register not integrated in sequence. An additional analog input for

one control sensor (if not already enabled for Heating 2 or El Heating 2).

InSequence

e.g. integrated as second cooling register in the sequence.

Fire damper fdbk

Fire damper feedback.

Closed

Only one feedback for close. Digital input.

Clsd+Opnd

Two separate feedbacks for open and close. Two digital inputs.

Combined

Two feedbacks for open and close, but only one signal. The syntax

must be correct 1->0->1 => Close-> Movement -> Open. Digital input.

Auxiliary input

No auxiliary input.

Input

An additional digital input for display only.

Alm

An additional digital input with alarm.

Inp+Alm

Two additional digital inputs. One for display and one with alarm.

Aux tmp sensor

No additional analog input.

Yes

Additional analog input to connect a temperature for display.

Aux TSP output

No additional digital output.

Yes

An auxiliary digital output controller by its own time switch program.

Aux A outp fan

No additional analog output.

Yes

Auxiliary analog output that provides a 0-10 V signal depending on the

present fan step.

Aux op mode

indicat

No additional digital output.

Yes

An additional digital output, switched dependent on present operating

mode (e.g. Comfort or Off).

Configuration 2

This parameters enable the plant after successful parameterization.

Enable occurs when Configuration 1, Configuration 2 and Configura-

tion IOs are completed, i.e. when each has the value "done".

NotDone

Plant locked against switching on.

Done

The plant is unlocked after complete parameterization (Configuration

2 and Configuration I/Os also have a value "done"), i.e. it can be

switched on.

Needed Required !! Passive

Execute

Reset required after successful parameterization in Configuration 2.

Assumes the appropriate presettings for Configuration I/Os.

After reset, value automatically goes from execute to passive.

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 166

Summary of Contents for Climatix Series





















































































































































































































































Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands

Siemens Climatix Series, Basis Document

Search results

Summary of Contents for Climatix Series

Reviews:

Brands by name

Popular brands