Siemens CL-110 User Manual Download Page 57

Page: 57 / 129

Chapter 3: Configuration

For Windows 2000

From the

Start

menu, point to

Programs

Accessories

and then click

Command Prompt

Type

ipconfig

at prompt. Then you

will see the IP information from DHCP
server.

If you want to get a new IP address, type

ipconfig /release

to release the

previous IP address and then type

ipconfig /renew

to get a new one.

For Windows XP

Type

ipconfig

at prompt. Then you

will see the IP information from DHCP
server.

From the

Start

menu, point to

Programs

Accessories

and then click

Command Prompt

Type

ipconfig

at prompt. Then you

will see the IP information from DHCP
server.

If you want to get a new IP address, type

ipconfig /release

to release the

previous IP address and then type

ipconfig /renew

to get a new one.

Summary of Contents for CL-110


































































































































Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands

Siemens CL-110, User Manual

Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands