Siemens CL-110 User Manual Download Page 13

Page: 13 / 129

Chapter 3: Configuration

For connecting through a hub, please refer to the following diagram for an example.

9 VAC

Install the USB Driver

For Windows ME

Run the USB installation program from the CD provided by your device package.

An InstallShield Wizard will appear. Please wait for a moment.

When the welcome screen appears, click

Next

for next step.

When the InstallShield Wizard Complete appears, click

Finish

Plug the USB cable between your device and PC.

Note: If the USB device is not detected, check the USB cable

between the PC and the device. Also verify that the device is
power on.

The system will detect the USB driver automatically.

Now, the system will copy the proper

files for this device.

When the file copying finished, the dialog above will close. Now the USB driver is installed
properly. You can use the device.

For Windows 2000

Run the USB installation program from the CD provided by your device package.

Summary of Contents for CL-110


































































































































Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands

Siemens CL-110, User Manual

Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands