Siemens CL-110 User Manual Download Page 17

Page: 17 / 129

Chapter 3: Configuration

The system is trying to find proper driver for your device and copying the files
automatically.

After the file copying is finished, a completing message will appear.

You can use the device now.

For Windows Vista

For Vista users, please press

Continue

whenever a prompted window asking for permission to

continue during USB driver installation process (see the figure below for example).

To install the USB driver before connect the router to the PC, here provides two methods.

Method One

– Use the driver CD came with the product package.

Run the USB installation program on the CD provided in your router package.

InstallShield Wizard

will appear. Please wait for a moment.

Summary of Contents for CL-110


































































































































Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands

Siemens CL-110, User Manual

Search results

Summary of Contents for CL-110

Reviews:

Related manuals for CL-110

Brands by name

Popular brands