background image

Legal information
Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage 
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices 
referring only to property damage have no safety alert symbol. These notices shown below are graded according to 
the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be 
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property 
damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific 
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. 
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and 
avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical 
documentation. If products and components from other manufacturers are used, these must be recommended or 
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance 
are required to ensure that the products operate safely and without any problems. The permissible ambient 
conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. 
Since variance cannot be precluded entirely, we cannot guarantee full consistency.  However, the information in this 
publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG
Smart Infrastructure
Electrical Products
Postfach 10 09 53
93009 Regensburg
GERMANY

3ZX1012-0TK28-0AC0
Ⓟ 06/2021 Subject to change

Copyright © Siemens AG 2010.
All rights reserved

Summary of Contents for 3TK2810-1



















































































Reviews: