manualshive.com logo in svg

Siemens 1PH728, Operating Instructions Manual

Share
Download
Siemens 1PH728 Operating Instructions Manual Download Page 55

 

Maintenance 

 

7.1 Maintenance 

A5E00177602A AD 
Siemens AG  Operating Instructions 2.02  1PH728 

53

 

The grease change intervals apply for normal loads, operation at speeds corresponding to 

those specified on the nameplate, precision-balanced running, almost neutral ambient air 

and the use of high-quality rolling-contact bearing greases. 

Grease types 

The following high-quality rolling-contact bearing greases have been tested and are suitable: 

Table 7-2 

Rolling-contact bearing greases 

K3N greases 
ESSO / Unirex N 3 
ARAL Aralub 4340 
DEA Glissando 30 
ESSO Beacon 3 
FUCHS Renolit FWA 220 
SHELL Alvania RL3 
WINTERSHALL Wiolub LFK 3 

These greases have lithium soap as the thickening agent and mineral oil as the base oil. 

They exceed the standard requirements of DIN 51825 in several important respects and are, 

therefore, compatible with the specified regreasing intervals.  

 

NOTICE 

 

Never mix greases that have different thickening agents and base oils. 

 

Initial lubrication 

ESSO Unirex N grease is used for initial lubrication of the bearings (prior to delivery). 

Siemens Hardware

Summary of Contents for 1PH728



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands