Siemens 1PH728 Operating Instructions Manual Download Page 41

Page: 41 / 82

A5E00177602A AD
Siemens AG Operating Instructions 2.02 1PH728

Start-up

4.1

Preparations

Safety note

WARNING

Only expert personnel should be entrusted with work on power installations.

Checking the insulation resistance

After long storage or shutdown periods, the insulation resistance of the windings must be

measured to ground with direct voltage.

CAUTION

Before you begin measuring the insulation resistance, please read the manual for the

insulation resistance meter you are going to use.

WARNING

Hazardous voltage
During the measurement, and immediately afterwards, hazardous voltage levels are

applied on some of the terminals and they should not be touched. Touching live

components can be result in death or serious injury.
Never touch the terminals when measuring or immediately after the measurement.
Check the supply feeder cables connected in order to ensure that the line supply voltage

cannot be connected.

●

Always measure the insulation resistance of the winding to the motor enclosure when the

winding temperature is between 20 and 30°C.

●

When measuring, wait until the final resistance value is reached; this takes approximately

one minute.

Siemens Hardware

Summary of Contents for 1PH728



















































































Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands

Siemens 1PH728, Operating Instructions Manual

Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands