Siemens 1PH728 Operating Instructions Manual Download Page 45

Page: 45 / 82

A5E00177602A AD
Siemens AG Operating Instructions 2.02 1PH728

Operation

5.1

Operation

Safety notes

WARNING

Please follow all instructions contained in the "Safety information and application

information (Page 7)" chapter of these operating instructions precisely and ensure that only

persons who have the necessary specialist know-how are entrusted to carry out work on

power installations.

WARNING

Rotating components
Covers prevent contact with live or rotating parts, or are used for proper air routing and thus

effective cooling of the motor.
Removing the covers during operation can result in death, serious injury, and property

damage.
Never open covers during operation.

CAUTION

Speed monitoring
The motor is designed for a certain speed range.
If a motor is operated at impermissible speeds damage to the winding, bearings, or

complete destruction of the motor can be the result.
Ensure that the speeds specified on the rating plate are not exceeded by appropriately

configuring controller and speed monitoring components.

Switching on

●

See the operating instructions of the frequency converter for switching on.

●

After starting the motor, observe it for a while to see if it is running smoothly and check

the monitoring devices.

Siemens Hardware

Summary of Contents for 1PH728



















































































Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands

Siemens 1PH728, Operating Instructions Manual

Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands