Siemens 1PH728 Operating Instructions Manual Download Page 17

Page: 17 / 82

A5E00177602A AD
Siemens AG Operating Instructions 2.02 1PH728

Description

2.1

Applications

Overview

Three-phase motors of the 1PH7 series are used as industrial drives. They have been

designed for a wide range of applications in the fields of drive engineering and power

conversion.
They are characterized by their high power density, ruggedness, long lifetime, and overall

reliability.
[ID: 301]

2.2

Siemens Service Center

Contact for further information

Details regarding the design of this electrical machine and the permissible operating

conditions are described in these operating instructions. If you have any questions or

suggestions, or if you require additional information, please contact the Siemens Service

Center:

Table 2-1

Technical support

Phone:

+49 (0)180 - 50 50 222

Europe - Germany:

Fax

+49 (0)180 - 50 50 223

America - USA:

Phone:

+1 423 262 2522

Asia - China:

Phone:

+86 1064 719 990

E-Mail:

[email protected]

Internet English:

www.siemens.com/automation/support-request

Internet Deutsch:

www.siemens.de/automation/support-request

Siemens Hardware

Summary of Contents for 1PH728



















































































Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands

Siemens 1PH728, Operating Instructions Manual

Search results

Summary of Contents for 1PH728

Reviews:

Brands by name

Popular brands