manualshive.com logo in svg

Siemens 1PH728, Operating Instructions Manual

Share
Download
Siemens 1PH728 Operating Instructions Manual Download Page 50

Faults 

 

6.1 Fault diagnosis table 

 

A5E00177602A AD 

48

 

Siemens AG  Operating Instructions 2.02  1PH728 

Table 6-2 

Diagnosis table for electrical faults 

Overview of electrical faults 
Electrical fault characteristics 
- Motor will not start up 
- Motor starts up slowly 
- Drumming noise during startup 
- Drumming noise during operation 
- Drumming noise in time with twice slip frequency 
- High temperature rise at no load 
- High temperature rise under load 
- High temperature rise of individual winding sections 

Note:  

If electrical faults occur, please refer to the manual 

for the frequency converter. 

Apart from eliminating the cause of the fault (as described under "Remedial measures"), you must also rectify any damage 

the motor may have suffered. 
Take into account possible changes due to a rise in temperature. 

[ID: 352.01] 

Summary of Contents for 1PH728



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands