Siemens 1LE5 Operating Instructions Manual Download Page 17

Page: 17 / 142

Figure 1-3

mySupport

The configured manual can be exported in RTF, PDF or XML format.

Siemens content that supports the mySupport documentation can be identified by the
"Configure" link.

1.4.5

Technical support

Description

Your routes to technical support (

https://support.industry.siemens.com/cs/ww/en/sc/4868

• Support Request (

https://www.siemens.com/SupportRequest

)

• Contact person database (

https://www.automation.siemens.com/aspa_app?lang=en

)

• "Industry Online Support" mobile app

The Support Request is the most important input channel for questions relating to products
from Siemens Industry. This will assign your request a unique ticket number for tracking
purposes. The Support Request offers you:

• Direct access to technical experts

• Recommended solutions for various questions (e.g. FAQs)

• Status tracking of your requests

Technical support also assists you in some cases via remote support (

https://

support.industry.siemens.com/cs/de/en/view/106665159

) to resolve your requests. A

Support representative will assist you in diagnosing or resolving the problem through screen
transfer.

More information on the Support service packages is available on the Internet via the
following address (

https://support.industry.siemens.com/cs/ww/en/sc/4869

Introduction

1.4 Service and support

1LE5, 1PC4 shaft heights 280 ... 355
Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands