Siemens 1LE5 Operating Instructions Manual Download Page 112

Page: 112 / 142

13.Install the outer bearing cover, if available.

14.Install the sealing elements:

9.4.3

Mounting dimension "x"

Mounting dimension "x" of V rings

Shaft height

280 ... 355

13.5 ±1.2

Standard design

Special design

• Extreme caution and attention to the correct positioning are vital during installation and

assembly.

• Make sure the sealing surface is free of dirt and damage.

• Lightly grease the sealing lips.

9.4.4

Fan

9.4.4.1

Metal fan disassembly

Metal fan

• Shaft height 63: Release the two M4 clamping screw so that the fan can rotate freely on the

shaft.

• Shaft heights 71...90: Release the M5 set screw so that the fan can rotate freely on the shaft.

• Shaft height 100...355: Remove the locking ring.

• Use a suitable tool to pull off the fan (puller).

• Locate the arms of the pulling tool in the openings in the fan in the vicinity of the hub.

• Alternatively, place the pulling tool at the outer edge of the fan plate.

• Uniformly withdraw the fan from the shaft by turning the pressure screw of the pulling tool.

Maintenance
9.4 Corrective maintenance

1LE5, 1PC4 shaft heights 280 ... 355

110

Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands