Siemens 1LE5 Operating Instructions Manual Download Page 98

Page: 98 / 142

Too much grease in bearing

Remove surplus grease.

Wrong grease in the bearing

Use the correct grease.

X Friction marks on raceway

Replace the bearing.

X Brinelling or scoring

Replace the bearing. Avoid any vibration at standstill

8.7.5

Faults at the external fan

The following table shows the possible causes of and remedial measures for faults on forced-
ventilated machines.

Table 8-4

Cooling system faults

↓ High temperature rise with load

Possible causes of faults

Remedial measures

Wrong direction of rotation of the separately
driven fan

Check the electrical connections to the separately driven fan.

Separately driven fan is not running

Check the separately driven fan and its connections.

Reduced air flow

Check the air ducts; clean the machine.

Operation
8.7 faults

1LE5, 1PC4 shaft heights 280 ... 355

Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands