Siemens 1LE5 Operating Instructions Manual Download Page 12

Page: 12 / 142

Information regarding third-party products

Note
Recommendation relating to third-party products

This document contains recommendations relating to third-party products. Siemens accepts the
fundamental suitability of these third-party products.

You can use equivalent products from other manufacturers.

Siemens does not accept any warranty for the properties of third-party products.

1.2.2

Target group

Description

These operating instructions are intended for:

• Fitters

• Commissioning engineers

• Machine operators

• Service and maintenance personnel

• Warehouse personnel

• Personnel decommissioning the motor

• Personnel disposing of the motor

1.2.3

Avoiding dangers

Description

Avoid dangers. Ensure safe, problem-free operation and a maximum service life:

• Before you start using the motor, you must read these Operating Instructions.

• Always follow the safety instructions and notices in these operating instructions.

The warning notice system is explained at the beginning of this document.

Introduction
1.2 About this manual

1LE5, 1PC4 shaft heights 280 ... 355

Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands