Siemens 1LE5 Operating Instructions Manual Download Page 110

Page: 110 / 142

①

Heat up 80 ... 100 °C

9.4.2.1

Bearing bushes

Protect the bearings against the ingress of dirt and moisture.

9.4.2.2

Fitting the bearing cartridges

When fitting the bearing cartridges, observe the specified screw tightening torques.

9.4.2.3

Installing bearings

Sealing the bearings

Note the following details:

• Shaft sealing rings are used to seal machines at the rotor shaft.

– For V rings, comply with the assembly dimension.

• Use the specified bearings.

• Ensure that the bearing sealing disks are in the correct position.

• Insert the elements for bearing preloading at the correct end.

• Fixed bearings can have a locking ring or bearing cover.

Maintenance
9.4 Corrective maintenance

1LE5, 1PC4 shaft heights 280 ... 355

108

Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands