Siemens 1LE5 Operating Instructions Manual Download Page 114

Page: 114 / 142

9.4.9

Reassembly: Miscellaneous information

• Position all rating and supplementary plates as in the original state.

• Where relevant, fix electric cables.

• Check the tightening torques of all screws, as well as those of screws that have not been

released.

9.4.10

Optional add-on units

Note
Further documents

Observe all of the other documents provided with this machine.

You can find additional operating instructions here: Siemens Industry Online Support on the
Web (Page 12)

9.4.10.1

Mounting a brake (optional)

Table 9-5

Assigning standard brakes for 1LE5 machines

Shaft height

Brake type

Size assignment of the

brakes

280

KFB100

100

280

FDX40

315

SFB 250-SH

250

355

SFB 400-SH

400

9.4.11

O-ring seal

If O-ring seals are present, you should check that they are in perfect condition and that the O-ring
seals are properly seated in the grooves between the components. Replace damaged O-ring
seals.

O-ring seals can be present on the following components, for instance:

• Adapters, tapers

• Entries, glands

• Bearing seals

• End shield seals

Maintenance
9.4 Corrective maintenance

1LE5, 1PC4 shaft heights 280 ... 355

112

Operating Instructions, 11/2022, A5E41454666A

Summary of Contents for 1LE5















































































































































Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands

Siemens 1LE5, Operating Instructions Manual

Search results

Summary of Contents for 1LE5

Reviews:

Related manuals for 1LE5

Brands by name

Popular brands