background image

35

 

Parameter 1:

Code of the settings menu. For more information consult 

Tab. 18.

 

Parameters 2 and 3 are the configuration or value options 

for each settings menu.

Select with buttons 

‘ ’

 or 

‘ ’

 to modify the menus 

or parameters.

All of the parameter settings are saved when the 

UPS is completely shut down and provided that it 

has connected batteries, whether internal or external.

If a complete shutdown is not carried out, the setting will 

not be saved to the memory.

7.3.4.  Settings.

Tab. 18 shows a summary of parameter 1’s adjustable codes for 

each operating mode.

 

DEPENDING ON THE DEVICE’S FIRMWARE 

VERSION, IT IS POSSIBLE TO SHOW SOME 

SCREENS IN ADDITION TO THOSE INDICATED 

IN THIS SECTION.

DO NOT CHANGE THE ORIGINAL FACTORY 

SETTINGS OF THESE, AS THIS COULD CAUSE 

FAULTS IN THE UPS, LOADS OR BOTH 

DEPENDING ON EACH SETTING.

Code

Description

Bypass mode/ 

No output 

mode

AC mode

ECO mode

CF mode

Battery mode Battery test

01

Output voltage.

YES

-

-

-

-

-

02

Output frequency.

YES

-

-

-

-

-

05

ECO enable/disable mode.

YES

-

-

-

-

-

08

Bypass mode setting.

YES

YES

-

-

-

-

09

Maximum battery discharge time setting.

YES

YES

YES

YES

YES

YES

10

Reserved.

Reserved for future options.

11

Reserved.

Reserved for future options.

12

Hot standby function 

YES

YES

YES

YES

YES

YES

17

Reserved.

Reserved for future options.

Tab. 18. 

Parameter 1 codes list. Description and settings

 

Code 01 - Output voltage.

Fig. 27. 

 

ˆ

Parameter 3 setting: Output voltage.

It is possible to choose one of the following values for 

the output voltage between phase and neutral:

 

208, 220, 230 or 240 V.

 

Code 02 - Output frequency.

Fig. 28. 

 

ˆ

Parameter 2 setting: Output frequency.

It is possible to choose one of the following values:

 

50 Hz, 60 Hz or ATO.

With ATO selected, the output frequency is auto-

detected according to the normal input at the time 

of connection of the device to the mains.

If it is between 46 and 54 Hz, it will be set at 50 

Hz, and, if it is between 56 and 64 Hz, at 60 Hz. The 

factory default setting is ATO.

 

ˆ

Parameter 3 setting: Frequency mode.

Output frequency in CF mode or not CF mode setting. It 

is possible to choose between two options:

 

CF. Sets the UPS to CF mode. With this option ac-

tivated, the output frequency is set to 50 or 60 Hz 

based on the parameter 2 selection. The input fre-

quency can be 46 to 64 Hz.

 

NCF. Sets the UPS to normal mode (not CF mode). 

With this option activated, the output frequency 

is set at 50 or 60 Hz synchronised with the input 

frequency based on the parameter 2 selection and 

its range.

If the parameter 2 selection is 50 or 60 Hz, it will be 

transferred to battery mode (powering loads) when 

the frequency is not respectively between 46 and 

54 Hz or 56 and 64 Hz.

(*)  If ATO is selected in parameter 2, parameter 3 will 

display the current frequency.

USER MANUAL        

 

 

 
 
 
 
 
 
 
 

 

 

 
 
 
 
 
 
 
 

Summary of Contents for SLC TWIN RT2 LION

















































Reviews: