background image

27

7.  CONTROL PANEL WITH LCD DISPLAY.

7.1.  GENERAL INFORMATION FOR THE SERIES.

7.1.1.  Information represented by the display.

Input voltage and 

battery information

Fault information

Information about 

battery charge level

Discharge time 

information

Information about 

the charge level 

connected to the 

output

Information about the operating mode of the device

Output voltage 

information

Audible alarm 

disabled

Fig. 21. 

Graphic and textual information shown on the display.

7.1.2.  Common messages shown on the LCD display.

Display

Meaning

Backup time information.

Indicates the backup time in analogue clock mode.

Indicates the backup time in digital clock mode.

H - Hours, M - Minutes, S - Seconds.

Fault information.

Indicates as a warning that a fault has occurred.

Indicates a numerical code from the settings menu shown in 

Table 9 of Section 7.5.

Audible alarm information.

Indicates that the audible alarm is disabled.

Output voltage information.

Indicates the output voltage or frequency. V AC - Output 

voltage, Hz - Output frequency.

Information about the charge level connected to the output.

Indicates the charge level connected to the output as a %, 

by displaying four equivalent segments respectively in the 

following proportion: 0-25 %, 26-50 %, 51-75 % and 76-100 

%.

Information about programmable outputs

P1

Indicates that the programmable outputs are activated.

Information about the operating mode of the device.

BATTERY

Indicates that the device is supplying output voltage from 

the battery (battery mode).

BYPASS

Indicates that the device is activated in ECO mode.

ECO

Indicates that the device is supplying output voltage from 

the bypass (ECO mode).

CHARGING

Indicates that the device is in charging mode.

CF/CVCF

Indicates that the device is in converter mode.

ONLINE

Indicates that the inverter is working.

P1

Indicates that the output is activated.

Information about battery charge level.

Indicates the battery charge level as a %, by displaying 

four equivalent segments respectively in the following 

proportion: 0-25 %, 26-50 %, 51-75 % and 76-100 %.

 

BATT 

FAULT

Indicates that the battery is not connected.

Indicates low battery voltage level.

Information about input and battery voltage.

Indicates the input voltage, frequency or battery voltage. 

V AC - Input voltage, V DC - Battery voltage, Hz - Input 

frequency.

Tab. 4. 

Information shown on the LCD panel of the control 

panel and its meaning.

USER MANUAL        

 

 

 
 
 
 
 
 
 
 

 

 

 
 
 
 
 
 
 
 

Summary of Contents for SLC TWIN RT2 LION

















































Reviews: