Shuttle HOT-597 User Manual Download Page 44 | Manualshive

Page: 44 / 45

background image

- 43 -

Onboard Serial Port 1/2

This item is used to define onboard serial port 1/Port2 to

3F8/IRQ4, 2F8/IRQ3, 3E8/

IRQ4, 2E8/IRQ3, Auto

or

Disabled.

UR2 Mode

The main board support IrDA(HPSIR) and Amplitudes Shift Keyed IR(ASKIR)
infrared through COM2 port. When IR is enable, the onboard COM2 port will be
disabled. This item specifies onboard Infra Red mode to IrDA 1.0, ASKIR, MIR
0.57M, MIR 1.15M, FIR or Standard (Disabled).
Note : FIR is not supported currently.

UR2 Duplex Mode

This item specifies onboard infrared transfer mode to full-duplex or half-duplex. This
item will not show up when IrDA, ASKIR, or MIR UR2 modes are sleected.

Onboard Parallel Port

This item specifies onboard parallel port address to

378H, 278H, 3BCH

or

Disabled

.

Parallel Port Mode

This item specifies onboard parallel port mode. The options are

SPP

(Standard Parallel

Port),

EPP

(Enhanced Parallel Port),

ECP

(Extended Capabilities Port), and

EPP

+

ECP

.

ECP Mode Use DMA

This item specifies

DMA

(Direct Memory Access) channel when ECP device is in use.

The options are

DMA 1

and

DMA 3

. This item will not show up when SPP and EPP

printer mode is selected.

«
...
42
43
44
45
»

Summary of Contents for HOT-597














































Reviews:

No comments

Related manuals for HOT-597

Brand: Data I/O Pages: 175

Brand: Datavan Pages: 15

Brand: Aaeon Pages: 65

Brand: Embest Pages: 91

Brand: ST Pages: 82

Brand: Gigabyte Pages: 116

Brand: Advantech Pages: 116

Brand: Texas Instruments Pages: 25

K8T8AS - REV 3.0

Brand: JETWAY Pages: 26

Brand: Supero Pages: 85

Brand: Texas Instruments Pages: 35

Brand: AOpen Pages: 8

Brand: DFI Pages: 96

Brand: Honda Pages: 132

GA-B150M-D3V DDR3

Brand: Gigabyte Pages: 4

Brand: MSI Pages: 118

Brand: Freescale Semiconductor Pages: 17

KINO-CV-KINO-CV-N26001

Brand: IEI Technology Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands