Shuttle HOT-597 User Manual Download Page 21 | Manualshive

Page: 21 / 45

background image

- 20 -

CPU, Chassis & AGP cooling Fan
connectors - Fan1, Fan2 & Fan3

The main board provides two onboard 12V
cooling fan power connectors for CPU (Fan 1),
AGP device (Fan 3) cooling fan. Depending
on the fan maker, the wiring and plug may be
different. The red wire should be connected to
+12V and black wire should be connected to
ground (GND).

Wake-On-LAN Connectors - J12

Attach a 3-pin connector from the LAN card
which supports the Wake-On-LAN (WOL)
function. This function lets users wake up the
connected system through the LAN card.

Enhanced IDE and Floppy
connectors

The main board shipped with one 40-pin ribbon
cable for IDE H.D.D, one 34-pin ribbon cable
for F.D.D. Ribbon cables should always be
connected with the red stripe on the Pin 1 side
of the connector.

Figure 2-8

«
...
19
20
21
22
23
...
»

Summary of Contents for HOT-597














































Reviews:

No comments

Related manuals for HOT-597

Brand: Panasonic Pages: 35

Brand: Intel Pages: 48

Brand: Lantronix Pages: 17

TLV320AIC3111 EVM

Brand: Texas Instruments Pages: 39

Brand: JETWAY Pages: 52

Brand: Gigabyte Pages: 96

Brand: Texas Instruments Pages: 21

Brand: IBASE Technology Pages: 81

Brand: Advantech Pages: 116

Brand: H-Tec Pages: 28

Brand: California Eastern Laboratories Pages: 34

Brand: ASROCK Pages: 106

Brand: Supermicro Pages: 107

Brand: MSI Pages: 106

Thunder HEsl S2567

Brand: TYAN Pages: 60

AR6MXCS- Series

Brand: BCM Pages: 9

Brand: MSI Pages: 48

MVME61006E-0161

Brand: Emerson Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands