Shuttle HOT-597 User Manual Download Page 20 | Manualshive

Page: 20 / 45

background image

- 19 -

Figure 2-7

Back Panel Connectors

COM1/COM2 Connectors

Attach COM1/COM2 device cables to these connectors.

PS/2 Keyboard & PS/2 Mouse Connector

Two 6-pin female PS/2 keyboard & Mouse Connectors is located at the rear of the main board.
PS/2 Mouse on top of connector and PS/2 Keyboard on the bottom of connector. Plug the PS/2
keyboard and mouse jack into this connector.

Parallel Port Connector

A 25-pin female connector is located at the rear of the main board. Plug the parallel port device
cable into this connector.

USB1/USB2 Port Connectors

Two female connectors are located at the rear of the board. Plug the USB devices jack into this
connector.

Other Connectors

ATX Power Supply Connector - J3

It is a 20-pin male header connector is connected to the ATX
power supply. The plug of the power supply will only insert in
one orientation because of the different hole shade and size.
Find the proper orientation and push down firmly making sure
that the pins are aligned.

IR Connector - JP3

Infrared device connector may attach a 5-pin infrared device
cable to this connector for enabling the infrared transfer func-
tion. This mainboard meets the specification of ASKIR and
HPSIR.

«
...
18
19
20
21
22
...
»

Summary of Contents for HOT-597














































Reviews:

No comments

Related manuals for HOT-597

Brand: IBM Pages: 357

Brand: E-peas Pages: 2

Industrial NUC-J6412

Brand: ASROCK Pages: 2

Brand: Texas Instruments Pages: 8

Brand: AXIOMTEK Pages: 2

Brand: Linear Technology Pages: 6

Brand: QDI Pages: 85

Brand: Texas Instruments Pages: 18

Brand: DFI Pages: 62

Brand: Silicon Laboratories Pages: 16

Brand: Gigabyte Pages: 84

Brand: ECS Pages: 66

Brand: Texas Instruments Pages: 18

Brand: Advantech Pages: 136

Brand: ECS Pages: 131

Brand: JETWAY Pages: 50

Brand: Linear Technology Pages: 8

TPS25944X635EVM

Brand: Texas Instruments Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands