Shuttle AV49V User Manual Download Page 32 | Manualshive

Page: 32 / 73

background image

- 28 -

F

Front Panel Connectors

HDD LED Connector (HDDLED)

Attach a connector cable from the IDE device LED to the 2-pin (HDDLED) header.
The HDD LED lights up whenever an IDE device is active.

Note : Please notice all the LED connectors are directional. If your chassis's

LED does not light up during running, please change it to the oppo-
site direction.

Hardware Reset Connector (RST)

Attach a cable to the 2-pin (RST) header. Pressing the reset switch causes the
system to restart.

C2

C1

PANEL1

HDDLED

RST

MSGLED

PWRBTN

1

+

_

+

_

PANEL1

HDDLED

RST

MSGLED

PWRBTN

1

+

_

+

_

«
...
30
31
32
33
34
...
»

Summary of Contents for AV49V










































































Reviews:

No comments

Related manuals for AV49V

DCDC SBC Series

Brand: Infineon Pages: 17

Brand: ECS Pages: 27

Brand: Ublox Pages: 23

Brand: Waveshare Pages: 72

Brand: Advantech Pages: 3

Brand: ASROCK Pages: 83

Brand: BCM Pages: 93

Brand: Gigabyte Pages: 37

Brand: MSI Pages: 85

Brand: Fastfame Pages: 41

Brand: Linear Pages: 16

LCMXO3L-DSI-EVN

Brand: Lattice Pages: 2

Brand: ASROCK Pages: 2

Brand: RIB Pages: 12

Brand: VIA Technologies Pages: 15

Brand: MSI Pages: 148

Brand: DFI Pages: 76

Brand: DFI Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands