Shuttle AV49V User Manual Download Page 7

Page: 7 / 73

- 3 -

CPU and Chassis Fan Connectors (CPUFAN1/CASFAN1) ................... 34

Audio CD_IN Connector (CD1) .............................................................. 34

Internal Speaker Header (SPEAKER1) .................................................. 34

3.3 SYSTEM MEMORY CONFIGURATION ..................................................... 35

1. INSTALL MEMORY ............................................................................ 35

2. UPGRADE MEMORY ........................................................................ 35

4 SOFTWARE UTILITY ...................................................................... 36

4.1 Mainboard CD Overview ......................................................................... 36

4.2 Install Mainboard Software ..................................................................... 37

4.2.A Install VIA 4in1 Driver .................................................................... 38

4.2.B Install VIA Audio Driver ................................................................. 39

4.2.C Install VIA USB2.0 Driver .............................................................. 40

4.2.D Install VIA LAN Driver (AV49VN Only) .......................................... 41

4.3 View the User's Manual ........................................................................... 42

5 BIOS SETUP ................................................................................... 43

5.1 ENTER BIOS ............................................................................................. 43

5.2 THE MAIN MENU ...................................................................................... 44

STANDARD CMOS FEATURES ............................................................... 46

ADVANCED BIOS FEATURES ................................................................. 49

ADVANCED CHIPSET FEATURES .......................................................... 52

INTEGRATED PERIPHERALS .................................................................. 56

POWER MANAGEMENT SETUP .............................................................. 59

PNP/PCI CONFIGURATIONS .................................................................... 63

PC HEALTH STATUS ................................................................................ 65

FREQUENCY/VOLTAGE CONTROL ......................................................... 66

LOAD FAIL-SAFE DEFAULTS .................................................................. 67

Summary of Contents for AV49V










































































Search results

Summary of Contents for AV49V

Reviews:

Related manuals for AV49V

Brands by name

Popular brands

Shuttle AV49V, User Manual

Search results

Summary of Contents for AV49V

Reviews:

Related manuals for AV49V

Brands by name

Popular brands