Shuttle AV49V User Manual Download Page 61

Page: 61 / 73

- 57 -

VIA OnChip PCI Device

Press <Enter> to enter into the detailed options.
VIA-3058 AC97 Audio
This item allows you to control the onboard AC97 audio.

The Choice: Auto or Disabled.

Onboard Lan Device (AV49VN Only)
This item allows you to enable or disable the onboard LAN.

The choice: Enabled or Disabled.

Onboard Lan Boot ROM (AV49VN Only)
Decide whether to invoke the boot ROM of the onboard LAN.

The choice: Enabled or Disabled.

SuperIO Device

Press <Enter> to enter into the detailed options.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC). If you
install add-on FDC or the system has no floppy drive, select Disabled.

The choice: Disabled or Enabled.

Onboard Serial Port 1
Select an address and corresponding interruption for the first serial port.

The choice: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,
or Auto.

Onboard Parallel Port
Allows you to determine an I/O address and interrupt request (IRQ) for
the onboard parallel port.

The choice: Disabled, 378/IRQ7, 278/IRQ5, or 3BC/IRQ7.

Parallel Port Mode
Select a mode for the onboard parallel (printer) port.

The choice: SPP, EPP, ECP, or ECP+EPP.

ECP Mode Use DMA
Select a DMA channel for the parallel port as using the ECP mode.

The choice: 1 or 3.

Game Port Address
This item defines an I/O address for the game port.

The choice: Disabled, 201, or 209.

Midi Port Address
This item defines an I/O address for the MIDI port.

The choice: Disabled, 330, or 300.

Summary of Contents for AV49V










































































Search results

Summary of Contents for AV49V

Reviews:

Related manuals for AV49V

Brands by name

Popular brands

Shuttle AV49V, User Manual

Search results

Summary of Contents for AV49V

Reviews:

Related manuals for AV49V

Brands by name

Popular brands