Shuttle AV49V User Manual Download Page 38 | Manualshive

Page: 38 / 73

background image

- 34 -

CPU and Chassis Fan Connectors (CPUFAN1/CASFAN1)

The mainboard provides two onboard 12V cooling fan power connectors to
support CPU (CPUFAN1) and Chassis (CASFAN1) cooling fans. Note that
both cable wiring and type of plug may vary, which depend on the fan
maker. Keep in mind that the red wire should always be connected to the
+12V header and the black wire to the ground (GND) header.

Audio CD_IN Connector (CD1)

Port CD1 is used to attach the audio connector
cable from the CD-ROM/DVD-ROM drive.

Internal Speaker Header (SPEAKER1)

Attach the PC speaker cable from the case to the
4-pin speaker connector (SPEAKER1).

E2

SENSE

GND

+12V

1

E3

E4

CASFAN1

CPUFAN1

SPEAKER1

1

1

CD1

«
...
36
37
38
39
40
...
»

Summary of Contents for AV49V










































































Reviews:

No comments

Related manuals for AV49V

Brand: Yamaha Pages: 83

EMB-APL1-A10-3350-F1-LV

Brand: Aaeon Pages: 42

IMBA-G412ISA-R20

Brand: IEI Technology Pages: 164

Brand: JETWAY Pages: 37

Brand: ECS Pages: 64

SUPER P4DPL-8GM

Brand: Supero Pages: 86

Brand: IWILL Pages: 48

Brand: JETWAY Pages: 19

Brand: H-Tec Pages: 28

Brand: Gigabyte Pages: 40

Brand: Infineon Pages: 11

Brand: TOHATSU Pages: 52

LCMXO3L-DSI-EVN

Brand: Lattice Pages: 2

Brand: ASRock Industrial Pages: 41

Brand: Gigabyte Pages: 120

Brand: TESSERA Pages: 31

SBC86620 Series

Brand: AXIOMTEK Pages: 90

PHANTOM GAMING B650E PG-ITX WiFi

Brand: ASROCK Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands