background image

 

 

 

1 

 

  

 

 

Illumisphere 50 

Product code: 41123 

Preface 

Thank you for purchasing this Showtec product. 

The purpose of this user manual is to provide instructions for the correct and safe use of this product. 

Keep the user manual for future reference as it is an integral part of the product. The user manual shall be 
stored at an easily accessible location. 

This user manual contains information concerning: 

 

Safety instructions 

 

Intended and non-intended use of the device 

 

Installation and operation of the device 

 

Maintenance procedures 

 

Troubleshooting 

 

Transport, storage and disposal of the device 

Non-observance of the instructions in this user manual may result in serious injuries and damage of 
property. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

©2020 Showtec. All rights reserved. 

No part of this document may be copied, published or otherwise reproduced without the prior written 
consent of Highlite International. 

Design and product specifications are subject to change without prior notice. 

For the latest version of this document, please visit our websit

www.highlite.com

 or contact us at 

[email protected]

. 

Highlite International and its authorized service providers are not liable for any injury, damage, direct or 
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or 
reliance on the information contained in this document. 

 

 

Summary of Contents for Illumisphere 50





























Reviews: